WDI1R Drop-in Anchor Short

Specifications and Packaging

Part No.	Code	Size	L	d0 (mm)	h0 (mm)	hmin (mm)	hnom (mm)	Rec. Tension Load C20/25 Concrete (kN)	Partial Safety Factor (yMc)	ETA	Pack 1
Part No.6103206	CodeWDI1R 6x25	SizeM6	L25 mm	d<subscript>0</subscript> (mm)8	h<subscript>0</subscript> (mm)≥ 25	h<subscript>min</subscript> (mm)80	h<subscript>nom</subscript> (mm)≥ 25	Rec. Tension Load C20/25 Concrete (kN)1.67*	Partial Safety Factor (yMc)1.50	ETAETA	Pack 1100
Part No.6103208	CodeWDI1R 8x25	SizeM8	L25 mm	d<subscript>0</subscript> (mm)10	h<subscript>0</subscript> (mm)≥ 25	h<subscript>min</subscript> (mm)80	h<subscript>nom</subscript> (mm)≥ 25	Rec. Tension Load C20/25 Concrete (kN)1.90*	Partial Safety Factor (yMc)1.50	ETAETA	Pack 1100
Part No.6103210	CodeWDI1R 10x25	SizeM10	L25 mm	d<subscript>0</subscript> (mm)12	h<subscript>0</subscript> (mm)≥ 25	h<subscript>min</subscript> (mm)80	h<subscript>nom</subscript> (mm)≥ 25	Rec. Tension Load C20/25 Concrete (kN)2.14*	Partial Safety Factor (yMc)1.50	ETAETA	Pack 150
Part No.6103212	CodeWDI1R 12x25	SizeM12	L25 mm	d<subscript>0</subscript> (mm)15	h<subscript>0</subscript> (mm)≥ 25	h<subscript>min</subscript> (mm)80	h<subscript>nom</subscript> (mm)≥ 25	Rec. Tension Load C20/25 Concrete (kN)2.14*	Partial Safety Factor (yMc)1.50	ETAETA	Pack 150

* = Recommended loads: are stated for multiple use for non-structural applications according to ETAG001, Part 6; apply to anchors correctly installed at maximum embedment depth; include partial safety factor and an overall partial safety factor for action of 1.4.
The partial safety factor for action depends on the type of loading and shall be taken from national regulations. All anchor failure modes and the entire relevant product European Technical Assessment must be considered for anchor design.
For more information, please refer to the ETA report.

simple and quick installation procedure
collar with a lip for flush anchor setting at any hole depth
medium load capacity
reduced 25 mm anchor length allows approved applications in precast prestressed hollow core slabs
material: steel
zinc plated
ETA ETAG001 Part 6 approval for multiple use for non-structural applications
fire resistance class R30-R120 for design of anchorages under exposure to fire
substrate type:
- cracked concrete
- non-cracked concrete

WDI1R Setting Tool Set
- combined tool for drilling and setting WDI1R anchors
- 50% faster installation than with traditional methods
- no uncomfortable hammering in overhead installations
For more information
WIS Brush
- each brush suitable for cleaning two hole diameters
- hybrid brush (steel and natural bristle)
- Part No. 609 9 981: single brush for M12 and M16 hole
For more information
WIS Blow Pump
- high blowing capacity
For more information
WDI1 SD Stop Drill Bit
- three cutting edges increase drilling speed
- designed for drilling all concrete at controlled depth
- particularly suitable for high volume installations of anchors such as WDI1
For more information
WSDS+ 3CE Concrete Drill Bit
- three cutting edges increase drilling speed
- designed for drilling all concrete
- drills through rebar without getting stuck
For more information
WSDS+ HB Hollow Block Drill Bit
- designed for drilling hollow bricks and blocks
- minimises damage done to the substrate
- long drill bit length allows drilling deep holes
For more information
WDI1R SD Stop Drill Bit
- designed for drilling all concrete at controlled depth
- particularly suitable for high volume installations of WDI1R Drop-in Anchors
- can be used as a replacement drill bit for WDI1R STS Setting Tool Set
For more information